Synthesis, Crystal Structure, and Broadband Emission of (CH3)3SSnCl3.

We report here on the synthesis, crystal structure, optoelectronic and vibrational properties, as well as the DFT calculations of the novel trimethylsulfonium tin trichloride (CH3)3SSnCl3. The air-stable compound is prepared by reacting the (CH3)3SCl and SnCl2 solid precursors in evacuated silica tubes at 100 °C. According to powder X-ray diffraction and Rietveld refinement, it crystallizes at room temperature in the orthorhombic space group Pbca (No. 61) with isolated pyramids of [SnCl3]- and (CH3)3S+ units. UV-vis reflectance and photoluminescence spectroscopies reveal a direct energy band gap of 3.85 eV, accompanied by a broad Stokes-shifted luminescence signal. Photoexcitation of the compound at room temperature and at -196 °C results in broadband luminescence with weak magenta emission centered at 400 nm using an excitation at 250 nm. First principal calculations provide insight into the physical properties through the electron and phonon density of states. Multitemperature Raman spectroscopy and differential scanning calorimetry reveal a reversible phase transition at ca. 70 °C that affects the vibrational modes of the [SnCl3]-. By dissolving (CH3)3SSnCl3 in dimethylformamide in ambient air for a week, oxidation of tin occurs in the "defect" perovskite ((CH3)3S)2SnCl6. The crystal structure of ((CH3)3S)2SnCl6 is also determined with high accuracy via single-crystal X-ray diffraction (cubic space group Pa-3 (No. 205)) and compared with (CH3)3SSnCl3 via Hirshfeld surface analysis.

Suppressing the Photocatalytic Activity of Zinc Oxide Electron-Transport Layer in Nonfullerene Organic Solar Cells with a Pyrene-Bodipy Interlayer.

Organic solar cells based on nonfullerene acceptors have recently witnessed a significant rise in their power conversion efficiency values. However, they still suffer from severe instability issues, especially in an inverted device architecture based on the zinc oxide bottom electron transport layers. In this work, we insert a pyrene-bodipy donor-acceptor dye as a thin interlayer at the photoactive layer/zinc oxide interface to suppress the degradation reaction of the nonfullerene acceptor caused by the photocatalytic activity of zinc oxide. In particular, the pyrene-bodipy-based interlayer inhibits the direct contact between the nonfullerene acceptor and zinc oxide hence preventing the decomposition of the former by zinc oxide under illumination with UV light. As a result, the device photostability was significantly improved. The π-π interaction between the nonfullerene acceptor and the bodipy part of the interlayer facilitates charge transfer from the nonfullerene acceptor toward pyrene, which is followed by intramolecular charge transfer to bodipy part and then to zinc oxide. The bodipy-pyrene modified zinc oxide also increased the degree of crystallization of the photoactive blend and the face-on stacking of the polymer donor molecules within the blend hence contributing to both enhanced charge transport and increased absorption of the incident light. Furthermore, it decreased the surface work function as well as surface energy of the zinc oxide film all impacting in improved power conversion efficiency values of the fabricated cells with champion devices reaching values up to 9.86 and 11.80% for the fullerene and nonfullerene-based devices, respectively.

Enhanced Organic and Perovskite Solar Cell Performance through Modification of the Electron-Selective Contact with a Bodipy-Porphyrin Dyad.

Photovoltaic devices based on organic semiconductors and organo-metal halide perovskites have not yet reached the theoretically predicted power conversion efficiencies while they still exhibit poor environmental stability. Interfacial engineering using suitable materials has been recognized as an attractive approach to tackle the above issues. We introduce here a zinc porphyrin-triazine-bodipy donor-π bridge-acceptor dye as a universal electron transfer mediator in both organic and perovskite solar cells. Thanks to its "push-pull" character, this dye enhances electron transfer from the absorber layer toward the electron-selective contact, thus improving the device's photocurrent and efficiency. The direct result is more than 10% average power conversion efficiency enhancement in both fullerene-based (from 8.65 to 9.80%) and non-fullerene-based (from 7.71 to 8.73%) organic solar cells as well as in perovskite ones (from 14.56 to 15.67%), proving the universality of our approach. Concurrently, by forming a hydrophobic network on the surface of metal oxide substrates, it improves the nanomorphology of the photoactive overlayer and contributes to efficiency stabilization. The fabricated devices of both kinds preserved more than 85% of their efficiency upon exposure to ambient conditions for more than 600 h without any encapsulation.

Photocatalysis as an advanced reduction process (ARP): The reduction of 4-nitrophenol using titania nanotubes-ferrite nanocomposites.

TiO2 photocatalysis is an advanced process, employed worldwide for the oxidation of organic compounds, that leads to significant technological applications in the fields of health and environment. The use of the photocatalytic approach in reduction reactions seems very promising and can open new horizons for green chemistry synthesis. For this purpose, titanium dioxide nanotubes (TNTs) were developed in autoclave conditions using TiO2 P25 as a precursor material. Based on these nanotubular substrates, TiO2/CoFe2O4 (TCF) nanocomposites were further obtained by wet impregnation method. The materials were thoroughly characterized and their structural, textural, vibrational, optoelectronic and magnetic properties were determined. The composite materials combine absorbance in the visible optical range and high BET surface area values (˜100 m2/g), showing extremely high yield in the photocatalytic reduction of 4-nitrophenol (4-NP), exceeding 94% within short illumination time (only 35 min). The developed nanocomposites were successfully reused in consecutive photocatalytic experiments and were easily removed from the reaction medium using magnets. Both remarkable recycling ability and high-performance stability in the photocatalytic reduction of nitrophenol were observed, thus justifying the significant economic potential and industrial perspectives for this advanced reduction process.

Engineering of Porphyrin Molecules for Use as Effective Cathode Interfacial Modifiers in Organic Solar Cells of Enhanced Efficiency and Stability.

In the present work, we effectively modify the TiO2 electron transport layer of organic solar cells with an inverted architecture using appropriately engineered porphyrin molecules. The results show that the optimized porphyrin modifier bearing two carboxylic acids as the anchoring groups and a triazine electron-withdrawing spacer significantly reduces the work function of TiO2, thereby reducing the electron extraction barrier. Moreover, the lower surface energy of the porphyrin-modified substrate results in better physical compatibility between the latter and the photoactive blend. Upon employing porphyrin-modified TiO2 electron transport layers in PTB7:PC71BM-based organic solar cells we obtained an improved average power conversion efficiency up to 8.73%. Importantly, porphyrin modification significantly increased the lifetime of the devices, which retained 80% of their initial efficiency after 500 h of storage in the dark. Because of its simplicity and efficacy, this approach should give tantalizing glimpses and generate an impact into the potential of porphyrins to facilitate electron transfer in organic solar cells and related devices.

Low Work Function Lacunary Polyoxometalates as Electron Transport Interlayers for Inverted Polymer Solar Cells of Improved Efficiency and Stability.

Effective interface engineering has been shown to play a vital role in facilitating efficient charge-carrier transport, thus boosting the performance of organic photovoltaic devices. Herein, we employ water-soluble lacunary polyoxometalates (POMs) as multifunctional interlayers between the titanium dioxide (TiO2) electron extraction/transport layer and the organic photoactive film to simultaneously enhance the efficiency, lifetime, and photostability of polymer solar cells (PSCs). A significant reduction in the work function (WF) of TiO2 upon POM utilization was observed, with the magnitude being controlled by the negative charge of the anion and the selection of the addenda atom (W or Mo). By inserting a POM interlayer with ∼10 nm thickness into the device structure, a significant improvement in the power conversion efficiency was obtained; the optimized POM-modified poly[[4,8-bis[(2-ethylhexyl)oxy]benzo[1,2-b:4,5-b']dithiophene-2,6-diyl][3-fluoro-2-[(2- 33 ethylhexyl)carbonyl]thieno[3,4-b]thiophenediyl]]:[6,6]-phenyl-C70 butyric acid methyl ester (PTB7:PC70BM)-based PSCs exhibited an efficiency of 8.07%, which represents a 21% efficiency enhancement compared to the reference TiO2 cell. Similar results were obtained in POM-modified devices based on poly(3-hexylthiophene) (P3HT) with electron acceptors of different energy levels, such as PC70BM or indene-C60 bisadduct (IC60BA), which enhanced their efficiency up to 4.34 and 6.21%, respectively, when using POM interlayers; this represents a 25-33% improvement as compared to the reference cells. Moreover, increased lifetime under ambient air and improved photostability under constant illumination were observed in POM-modified devices. Detailed analysis shows that the improvements in efficiency and stability synergistically stem from the reduced work function of TiO2 upon POM coverage, the improved nanomorphology of the photoactive blend, the reduced interfacial recombination losses, the superior electron transfer, and the more effective exciton dissociation at the photoactive layer/POM/TiO2 interfaces.

Trimethylsulfonium Lead Triiodide: An Air-Stable Hybrid Halide Perovskite.

We report on the synthesis, characterization, and optoelectronic properties of the novel trimethylsulfonium lead triiodide perovskite, (CH3)3SPbI3. At room temperature, the air-stable compound adopts a hexagonal crystal structure with a 1D network of face-sharing [PbI6] octahedra along the c axis. UV-vis reflectance spectroscopy on a pressed pellet revealed a band gap of 3.1 eV, in agreement with first-principles calculations, which show a small separation between direct and indirect band gaps. Electrical resistivity measurements on single crystals indicated that the compound behaves as a semiconductor. According to multi-temperature single-crystal X-ray diffraction, synchrotron powder X-ray diffraction, Raman spectroscopy, and differential scanning calorimetry, two fully reversible structural phase transitions occur at -5 and ca. -100 °C with reduction of the unit cell symmetry to monoclinic as temperature decreases. The role of the trimethylsulfonium cation regarding the chemical stability and optoelectronic properties of the new compound is discussed in comparison with APbI3 (A = Cs, methylammonium, and formamidinium cation), which are most commonly used in perovskite solar cells.

Structural Stability, Vibrational Properties, and Photoluminescence in CsSnI3 Perovskite upon the Addition of SnF2.

The CsSnI3 perovskite and the corresponding SnF2-containing material with nominal composition CsSnI2.95F0.05 were synthesized by solid-state reactions and structurally characterized by powder X-ray diffraction. Both materials undergo rapid phase transformation upon exposure to air from the black orthorhombic phase (B-γ-CsSnI3) to the yellow orthorhombic phase (Y-CsSnI3), followed by irreversible oxidation into Cs2SnI6 within several hours. The phase transition occurs at a significantly lower rate in the SnF2-containing material rather than in the pure perovskite. The high hole-carrier concentration of the materials prohibits the detection of Raman signals for B-γ-CsSnI3 and induces a very strong plasmonic reflectance in the far-IR. In contrast, far-IR phonon bands and a rich Raman spectrum are observed for the Y-CsSnI3 modification below 140 cm-1 with weak frequency shift gradients versus temperatures between -95 and +170 °C. Above 170 °C, the signal is lost due to B-α-CsSnI3 re-formation. The photoluminescence spectra exhibit residual blue shifts and broadening as a sign of structural transformation initiation.

Reentrant Structural and Optical Properties and Large Positive Thermal Expansion in Perovskite Formamidinium Lead Iodide.

The structure of the hybrid perovskite HC(NH2 )2 PbI3 (formamidinium lead iodide) reflects competing interactions associated with molecular motion, hydrogen bonding tendencies, thermally activated soft octahedral rotations, and the propensity for the Pb2+ lone pair to express its stereochemistry. High-resolution synchrotron X-ray powder diffraction reveals a continuous transition from the cubic α-phase (Pm3‾ m, #221) to a tetragonal ß-phase (P4/mbm, #127) at around 285 K, followed by a first-order transition to a tetragonal γ-phase (retaining P4/mbm, #127) at 140 K. An unusual reentrant pseudosymmetry in the ß-to-γ phase transition is seen that is also reflected in the photoluminescence. Around room temperature, the coefficient of volumetric thermal expansion is among the largest for any extended crystalline solid.